What are Commonly Used Milling Cutter Coatings?
The roble had hit a record low after the West imposed sweeping sanctions on Russia for its aggression in Ukraine. Russia's president recently ordered exports of Russian gas to "unfriendly" countries to be settled in robles. The speaker of Russia's upper house of parliament said Moscow was prepared and could shift supplies to markets such as Asia if Europe refused to buy Russian energy.
European countries, which pay mostly in euros, say Russia has no right to reset contracts. The G7 rejected Russia's demand and urged companies not to agree to pay in robles, saying most contracts stipulated payment in euros or dollars. Wholesale gas prices in Europe have risen further recently on concerns about potential supply disruptions.
The Kremlin spokesman said, "According to the March 31 deadline set by Russia's president, we are developing all payment methods to get a simple, understandable, and feasible system for relevant European and international buyers,"
The markets and prices of more commodities like the TiN powder would be affected because of the volatile international political situations.
I. Titanium nitride coating (TiN)
TiN coating is a universal PVD coating that improves tool hardness and oxidation temperature. The coating can be used for high-speed steel cutting tools or forming tools to obtain good machining results. TiN coating is pretty economical, it is used to extend the service life of general tools and molds. Its performance is particularly outstanding when it is used to cut copper, low carbon steel, and other soft metals. Coating TiN on the surface of milling cutter can effectively improve the surface hardness of milling cutter, reduce the chemical affinity of milling cutter, prevent adhesion damage in the process of machining, and improve the wear resistance of the milling cutter.
2. Titanium nitrogen carbide coating (TiCN)
The carbon added to the TiCN coating improves tool hardness and surface lubricity, making it an ideal coating for tools. Due to the introduction of carbon element, the surface lubricity of the coating is improved and the friction coefficient is reduced. At the same time, the internal stress of the coating is reduced, which is of great significance to improve the production efficiency and surface quality of the workpiece. TiCN coating has lower friction coefficient and higher hardness than TiN coating. The milling cutter coated with titanium nitride carbide is more suitable for milling stainless steel, titanium alloy, nickel alloy and other hard materials. It has stronger wear resistance and high temperature stability, and can significantly improve the tool life.
3. Titanium aluminum nitride coating (AlTiN)
The alumina layer formed in the AlTiN coating can effectively improve the high temperature machining life of the tool, and the stable oxide layer is formed on the interface between the tool front and chip during cutting, which has good heat insulation performance. AlTiN coatings provide higher surface hardness than TiAlN coatings based on the ratio of aluminum to titanium in the coating, making it a viable alternative coating for high speed machining.
4. Aluminum chromium nitride coating (AlCrN)
AlCrN coating exhibits good red hardness and high temperature stability under high temperature conditions, and has good thermal corrosion performance. When machining low hardness materials or high viscosity materials, the cutting performance is better than AlTiN coated tools. Good adhesion makes it a coating when treating nodules. With this almost invisible coating, milling cutter performance will be greatly improved.
5. CVD diamond coating
Different from single-crystal diamond cutter and PCD composite cutter, CVD diamond coated cutter is a CVD diamond coated cutter which is deposited on the surface of carbide cutter by chemical vapor deposition (CVD) method. In the CVD diamond coating process, the tool surface is pure diamond without any additives, which avoids the application limitations caused by the presence of additive metals in PCD composite films. And the whole deposition process is carried out in atmosphere, there is no special requirement for tool geometry, which can be in any shape of carbide tool surface coating, to meet the needs of complex contour processing.
After experimenting and validation of various cutting tool materials, the service life of CVD diamond coated tools is 8-10 times that of carbide, and its cutting speed is 2-3 times higher than that of cemented carbide cutting tools. It has a good consistency and a low friction factor.
Luoyang Tongrun Nano Technology Co. Ltd. (TRUNNANO) is a trusted global chemical material supplier & manufacturer with over 12-year-experience in providing super high-quality chemicals and nanomaterials including silicon powder, nitride powder, graphite powder, zinc sulfide, calcium nitride, 3D printing powder, etc.
If you are looking for high-quality chemicals, please feel free to contact us and send an inquiry. ([email protected])
U.S. oil prices surged about 10% to $105.14 a barrel. This is the highest level since 2014. The world benchmark Brent stock futures oil price soared by about 8% to $105.40 per barrel. The most direct rise in crude oil is inflation. The rise in oil prices means that people's food, clothing, housing, TiN powder also fluctuates. If you want to know the TiN powder, please feel free to contact us.